How to remove a dent in the refrigerator

In which case can the problem be fixed? There can be many reasons for dents on the refrigerator - blows during moving, when moving in an apartment, etc. If the defect is significant, there is damage to the paintwork, then it will not be possible to eliminate the problem without involving a specialist and appropriate equipment. If the damage is small, then you can try to fix it yourself.

Work Precautions

Below will be presented various ways to eliminate the defect on the surface of the refrigerator. Some of them are associated with certain health risks and for the equipment being repaired. Therefore, it is important to observe some precautions.

Using dry ice to create contrasting temperatures, you must use protective gloves and avoid contact with unprotected parts of the body. It is also important that the room in which the work will be carried out is well ventilated.

Using a rubber mallet and trowel to correct, you must try to carry out repairs carefully so as not to aggravate an existing problem. If there is no experience working with damaged metal surfaces, then it makes sense to exercise a little on metal pieces that are as similar as possible to the elements of the refrigerator.

Attention! Disassembling the door in order to eliminate unevenness on its surface is not recommended. Otherwise, there is a high risk of leakage and loss of its original form.

Ways to fix a defect

How to level a surface using contrasting temperatures

First you need to thoroughly clean the dented area. You can use a soft rag, paper towels. Next, along the perimeter of the damage, the metal is heated using a hair dryer. Processing time is approximately a minute. During heating, the metal will expand, but care must be taken not to overheat the area. Otherwise, the seal inside the wall may be damaged.

Next, dry ice is applied to the dent, it can be bought at the pharmacy. It is better to wrap a piece in suede fabric to protect the surface from scratches. Circular movements carry out the processing of the site for a minute, after which the rag with dry ice is removed.

If a characteristic clap is heard, it means that the metal has managed to return to its normal (or close to this) position due to the temperature contrast. If the defect failed to be fixed the first time, it is worth repeating the procedure again.

How to remove a dent in a refrigerator with a car suction cup

If there is a vacuum suction cup in the arsenal, then straightening the pressed metal with it will not be difficult. If not, you should buy it at an auto parts store. True, the price of the device is quite high.

Similar to the above method, the treated surface must be cleaned and degreased. Next, the adhesive composition that comes with the device is applied to the surface of the suction cup. Then it is placed in the center of the dent.

After the glue dries, the device itself is put on the suction cup, somewhat reminiscent of a small rocker. At its edges are rubber gaskets, thanks to which neighboring metal sections are not damaged. A special adjusting knob, screwed onto the threaded end of the suction cup, begins to pull the metal. After fixing the defect, the device is dismantled, the remaining glue is washed off with water or a special composition is used for these purposes.

Trowel and rubber hammer against a dent in the refrigerator

Important! It is strictly forbidden to carry out mechanical impact on the damaged surface of the refrigerator with an ordinary hammer. Violation of the paintwork will no longer allow you to qualitatively fix the defect yourself.

Therefore, for straightening, you will need a trowel and a rubber hammer. Having no experience in performing such work, it is better to prefer other methods. It is first necessary to clean the surface. Further, the perimeter of the dent warms up with a hairdryer, after which the defect is completely blocked with a trowel. Slight strokes on the trowel will give a resonance effect, as a result of which the dent should straighten.

Correcting a defect with compressed air

If at home there is a can of compressed air used to clean the computer and accessories from dust, then you can use it to fix the damage. Turning the can upside down, you need to spray a small amount of the substance. With this method, cold condensate forms, which cools the metal surface to compression temperatures. If the surface does not return to its original state, it makes sense to repeat the procedure several more times.

Dent decoration

Putty to help

You can decorate an eye-catching defect with a primer and putty. First, it is necessary to clean the area with fine-grained emery paper, then ground the unevenness. After the primer dries, the dent is plastered. It is desirable that the color of the putty is extremely close to the color of the refrigerator itself. As a rule, it is extremely rare that a damaged area after work is invisible, especially when it comes to a glossy surface.

Other decorative products

If the ideal result with putty could not be obtained or there is simply no desire to carry out repair work, you can try to close the defect with decorative magnets. In addition to magnets, it is worth using special decorative films that perfectly hide all damage. There are many original design solutions on the market, it will be easy to find a suitable option.

Watch the video: How To Remove a DingDent From a Refrigerator Door Samsung, LG, GE, Frigidaire, Kenmore (March 2024).

Leave Your Comment