After buying a dishwasher, it becomes necessary to connect it to the water supply system, sewage system and the power supply network. There are two ways - either without thinking twice about calling a master who will do everything for the appropriate fee, or by connecting the dishwasher yourself. How difficult is it? It all depends on whether a person is able to hold tools in his hands, and whether the connection process itself is representative.
The article will describe the list of necessary tools, the connection procedure, the features of connecting certain types of PMM, as well as the procedure for checking the device after connection.
Preparatory stage
What tools and materials will be needed when connecting the dishwasher
To connect the PMM you will need:
bronze or brass (not silumin!) tee crane;- clamps;
- pliers, screwdriver, wrench, wire cutters, teflon tape or tow;
- branch siphon;
- grounded outlet.
bronze or brass (not silumin!) tee crane;There may be troubles like a too short power cord, hoses, improper gaskets and the like. In this case, you will have to increase the hoses, buy gaskets, use an extension cord - in a word, additional costs and fuss are possible.
Recommended Workflow
Manufacturers attach step-by-step instructions for connecting dishwashers, often the sequence of connection varies. Instructions for connecting the machine can say one thing, but in practice the proven sequence is as follows:
- connect the PMM to the sewer system;
- connect to the water supply;
- apply power;
- trial inclusion and testing;
- installation of the machine in its place - in a niche, under the countertop, etc.
You can, of course, connect in a different sequence, if the hunt tinkers longer.
Features of connecting dishwashers of different brands
For Bosch machines, it is very important to correctly install the gasket, otherwise, after a couple of cycles of operation, it will begin to pass water. In addition, the feed valve for machines of this brand is very sensitive, so you will have to put a rough water filter in the system.
Regarding the Siemens brand, it’s the most unpretentious installation technique, with the exception of strict requirements for the size of the built-in niche and for fastenings.
When installing the Electrolux PMM, it is important to position it exactly in level, the allowable slope should not exceed 2 degrees.
Dishwasher connection
How to install a dishwasher
The installation procedure was discussed above, the place for the PMM must meet the following requirements:
- the niche should correspond to the size of the machine, it is important to clearly measure its dimensions before buying PMM;
- fastening under the dishwasher is used either standard, which is included in the kit, or according to the model given in the instructions;
- the instructions provide the correct position of the dishwasher relative to the horizon - so it should be mounted;
- Do not allow water to enter the wiring harness or the power connectors.
How to connect the drain and water supply
First of all, it is necessary to put a sewer siphon with a fitting (or two, when connecting the PMM and the washing machine).
When connecting the dishwasher to the drain, please note:
- in the place of connecting the hose with a fitting, you need to make a v-shaped bend that provides a natural drainage of water from the machine, while the water does not stagnate and does not return;
- the knee should be below, in order to avoid an unpleasant odor in the PMM;
- If possible, to avoid overloading the pump, do not extend the drain hose.
The easiest way to connect water to the dishwasher is through a mixer. To do this, you need:
- shut off water supply;
- disconnect the hose from the mixer, while removing the old insulation;
- connect a tee with a tap to a pipe with cold water;
- connect the mixer hose to one outlet of the tee, and the coarse filter to the other; the inlet hose of the dishwasher is connected directly to the filter.
Screw the inlet hose with force, but without the use of keys.
How to connect the machine to electrical networks
It is only necessary to connect the PMM to the power supply system through a separate grounded outlet. The use of extension cords is highly undesirable, and it is also not recommended to connect refrigerators, washing machines and other devices together with the dishwasher to the mains power supply due to the high power consumption. It is recommended to conduct a separate power supply to the dishwasher from the electric meter. If there is no time, desire or skills - use the help of specialists.
How to test a dishwasher after connecting
To check the PMM, you can start it without loading the dishes, adding salt and powder. According to the attached instructions, we start the car and look at the result. A trial run makes it possible to verify the correct connection to the power supply, the absence of leaks and normal water supply. Particular attention should be given to checking for leaks. After a trial run, the dishwasher is mounted on its regular place.
Leave Your Comment